Walk-in Closets
A closet built to the room, not a kit that stops eight inches short of the ceiling. We do this across Monmouth and Ocean County from Ocean Township. Call and we come look before we write the scope.
- 5.0 on Google
- Licensed #13VH09886800
- Phone answered 24/7
Walk-in Closets, on one written scope.
A closet built to the room, not a kit that stops eight inches short of the ceiling.
What’s included on a walk-in closets visit.
We inspect the cause, check what else it touched, and leave a written scope with materials and timing. The visit is free and there is no obligation to book the work.
What to know before the visit.
Have ready
Empty the closet and take everything off the rods and shelves before we arrive. If you want drawers or a hamper, decide the count and where they go. Have the door and any mirror on site if you bought them. The first three things we check are the actual ceiling height at both ends of the room, the wall construction and stud locations, and the door swing and the clearance it needs. We also check for a light box and whether the floor is level.
- Layout
- Rods and shelves
- Drawers
- Doors
The visit
We measure the room, including the ceiling height and the door swing, and we build to that instead of a kit that stops short. Rods are at two heights where the ceiling allows. Drawers are in a box that is fastened to the wall, not a tower that tips when the top drawer is full.
A walk-in under a stair in a colonial gets a custom end, not a shelf system that pretends the ceiling is flat. The sloped end is where the storage usually is, and it is where kits fail.
Permit
Rods, shelves, and drawer boxes are finish carpentry and normally need no permit. Adding a light or a switch to a closet is electrical work, and most towns want a permit and an inspection for a new circuit, though swapping a fixture on an existing box usually does not. Widening a door opening or adding a wall is structural and does need one. If the closet is part of a larger renovation already under permit, the work is covered by that permit. We confirm before we cut.
On the Shore
A closet in a shore house is often the dampest room in it. Humidity and a closed door make it worse, and that is what this assembly has to survive. Particleboard and MDF swell at the cut edges and the shelf sags, then the fasteners pull. Steel rod brackets and wire shelving rust and stain clothes. We use plywood or a moisture-resistant panel, seal the cut edges, and keep solid wood or coated rods with brackets into studs so the weight is not hanging on drywall.
When we leave
When the boxes are set we load a shelf and a rod with weight and watch for sag or a bracket pulling, then cycle every drawer and door through its full travel. Doors get checked for the reveal and for rubbing at the top and the latch side. Adjustable shelves get moved to the heights you want before we leave. We hand over the leftover touch-up and tell you the load each rod is set for, so you do not hang winter coats on a shelf standard.
Built with
We build from plywood or melamine-faced panels with a solid-wood or plywood edge band, and we fasten the boxes to studs with cabinet fasteners. Rods are chrome, coated steel, or wood in a center support if the span is long. Shelf standards and brackets are steel or aluminum. Drawers run on side-mount or under-mount slides rated for the load. Adjustable shelves get pin holes or standards, and any new piece gets primed or finished so bare panel edges do not drink humidity.
Do you paint the inside?
If the scope includes it. Bare MDF in a closet looks unfinished, so we at least prime the new pieces.
Lighting?
A surface fixture on an existing box, or a new switch if we are already doing electrical in the room. A closet with no light is a different kind of unfinished.
Can you keep the existing rod and add drawers?
If the rod is in a stud and at a usable height. A sagging rod gets replaced while we are there.
Shoe shelves?
Angled, at a height you can reach, ventilated if the closet is damp. A shore-house closet that smells like a basement needs the moisture looked at, not just a shelf.
Doors?
We can hang a pair if the opening is framed for it. Widening an opening is carpentry with a header, and we quote that separately.
How long?
A single reach-in conversion is a day. A full walk-in with drawers is longer because the boxes are built to the room.
Can you work around a sloped ceiling or a stair?
Yes, that is where a built-to-the-room closet earns its place. We scribe the end panel to the slope and use the low side for drawers, with the high side for double rods. A kit leaves that space empty.
How deep should the shelves be?
Twelve inches is standard for clothes, and fourteen for folded stacks or a hamper. Deeper than that and the back is wasted. We set the rod about eleven inches off the back wall so hangers sit square and clothes do not brush the wall.
Will the drawers hold up in a damp room?
With plywood or moisture-resistant boxes and slides that are rated, yes. The failure point is the cut edge and the fastener, so those get sealed. We keep the box off the floor on adjustable feet or a plinth rather than sitting it in any damp.
Do you remove the old wire shelving?
Yes, and we patch the holes so they do not telegraph through paint. Wire shelving is usually fastened with plastic anchors that have already wallowed out. We fill those and hit them with primer before the new standards go up.
Other carpentry jobs we handle
Cabinets
Install, adjust, and refacing-level repairs for kitchens that stick and doors that will not close.
Countertops
Set a new top, scribe the splash, and reconnect the sink.
Curtain and Picture Hanging
The small job. Anchors in the stud when the art is heavy, plaster anchors when it is not.
Deck Installation and Repair
New decks and the boards, rails, and ledgers that fail first on the Shore.
Tell us what is wrong. We will tell you what it takes.
(732) 333-7800- Call24 hours a day, 7 days a week
- Shop7 Brook Dr, Ocean Township, NJ 07712
- EmailInfo@wedoitallhandyman.com
- EstimateFree on-site look. Written scope before work starts.
Licensed & insured · NJ HIC # 13VH09886800
Free on-site look · No obligation