HVAC Duct Work
Fallen flex, missing returns, and bath fans that blow into the attic. We do this across Monmouth and Ocean County from Ocean Township. Call and we come look before we write the scope.
- 5.0 on Google
- Licensed #13VH09886800
- Phone answered 24/7
HVAC Duct Work, on one written scope.
Fallen flex, missing returns, and bath fans that blow into the attic.
What’s included on a hvac duct work visit.
We inspect the cause, check what else it touched, and leave a written scope with materials and timing. The visit is free and there is no obligation to book the work.
What to know before the visit.
Have ready
Clear a path to the attic hatch or crawl space, move stored boxes away from the hatch, and know which rooms run hot or cold in summer and winter. Note where the thermostat sits and whether any register has been closed. The tech first walks the trunk and branch runs looking for flex that has fallen off a collar or been crushed, then checks that every supply damper at the trunk is actually open, then confirms that bath fan and dryer exhausts terminate outdoors with a real cap and not into the insulation.
- Reconnect runs
- Seal the obvious leaks
- New registers
- Fan duct to outdoors
The visit
Fallen flex in an attic is reconnected and supported, not left draped over a truss. Bath fans that dump moist air into the insulation get a duct to a real cap. A new register after a remodel is cut only after we know which joist bay the run is in.
The room that never cools in a Tinton Falls split-level is often a crushed flex elbow above the hallway. Balancing dampers do nothing if the run is pinched shut.
Permit
Reconnecting a fallen run, replacing a register, or sealing joints on duct you already have is maintenance and normally needs no permit in New Jersey. A permit is normally not required for that. Adding a new return, extending a trunk, or installing duct for a new system is mechanical work that gets filed and inspected through the local construction office. If the work touches the air handler or gas appliance venting, that changes the scope and gets settled first.
On the Shore
Attic ductwork near the Shore lives in a brutal space. Summer humidity and winter freeze-thaw cycles sweat the metal trunk and the boots, and salt air pits the sheet metal and corrodes the hangers, screws, and foil facing. Insulation that gets wet loses its value and stays wet against the duct, which is where mold starts. Runs that stay sealed, supported off the joists, and fully insulated hold their performance; draped and pinched flex does not.
When we leave
Every register the tech touched gets checked for airflow with a hand and a tissue, and the returns get confirmed by feel. The blower runs through a full heating and cooling cycle, and the tech listens at the nearest boot for the whoosh that means a run is still pinched. A new bath fan duct gets confirmed at the exterior cap, with the damper flapping freely, not stuck shut. Filters go back in the right direction and the access panel is closed.
Built with
The usual parts are insulated flexible duct for branch runs, rigid sheet metal trunk and fittings, foil tape and mastic for seams, nylon or metal duct strapping, and sealed register boots with a proper collar. Registers are metal or high-impact polymer with a damper. Bath fan duct is smooth rigid or insulated flex sized to the fan, terminated at a wall or roof cap with a backdraft damper. Mastic goes on metal joints that can be reached.
Can you add a return?
If the joists run the right way and we can reach the trunk. A return in a specific wall is a maybe until we see the framing.
Do you replace all the ductwork?
Only when it is collapsed, full of debris, or the wrong size for a new air handler. A solid metal trunk stays.
What about a disconnected dryer vent while you are up there?
We reconnect it to the outside if we are already in that bay. Lint in the attic is a fire note, not a side comment.
Will new ducts fix a hot upstairs?
If the upstairs run is open and sized. If the air handler is short of capacity, ducts are not the whole answer, and we say so.
Do you seal with mastic or tape?
Mastic on metal joints we can reach. Foil tape is for the flex collar, not for a gaping seam.
How do you keep insulation out of the boot?
The boot gets fastened and the insulation stays on the attic side of the drywall, not inside the airstream.
Why is one room always warm when the rest is fine?
A single bad room points at the run feeding it, not the whole system. A disconnected collar, a crushed elbow, a closed damper, or a boot buried under insulation will do it. We trace that one run before we talk about balancing anything.
Can you run a duct through a finished ceiling?
Sometimes with a soffit or a closet chase, and sometimes not without cutting drywall. We look at the joist direction and what is above before we promise a path, and we tell you what patching would be needed.
Is a noisy vent a duct problem?
Usually yes. A run that is undersized, pinched at a fitting, or missing a return path will whistle. We check the takeoff and the boot, and if the noise is really the blower, we say that instead of selling ductwork.
Do registers need to stay open in unused rooms?
Closed registers on a forced-air system raise the pressure in the trunk and can starve other rooms. We set dampers at the trunk rather than shutting the face, and we mark the ones we adjusted so you can put them back.
Other hvac jobs we handle
AC Installation and Replacement
System replacement sized to the house, with the line set and the air handler done like a new install.
Furnace and Heating Repair
No heat, short cycling, or a pilot that will not stay lit on an older furnace.
Ductwork Repair and Sealing
Fallen flex, crushed runs, and leaks at the takeoffs, sealed where they can be reached.
Thermostat and Controls
A thermostat that reads the wrong temperature or cannot call the right stage.
Tell us what is wrong. We will tell you what it takes.
(732) 333-7800- Call24 hours a day, 7 days a week
- Shop7 Brook Dr, Ocean Township, NJ 07712
- EmailInfo@wedoitallhandyman.com
- EstimateFree on-site look. Written scope before work starts.
Licensed & insured · NJ HIC # 13VH09886800
Free on-site look · No obligation